Views: 0 Author: Site Editor Publish Time: 2024-11-01 Origin: Site
Advantages of KN620-3:
1.Rotatable LCD screen for easier operation
2.Heightening the machine head can seal higher edge strips, upgrading from 8-50mm to 14-70mm
3.Machine head rotation, 15°/0/-15°, three angles, increases plate compatibility, operates more plates, and is more flexible
4.Glue pot, 2600ml, dual-purpose PUR and EVA, internal Teflon coating, one-click glue discharge, easy glue replacement
5.Layered board design, precision design, fixed edge banding is not easy to deviate, and is done right from the first step
6.Secondary auxiliary pressure roller, the edge banding strip and the plate are pressed twice to increase the adhesion
7.Anti-reverse walking plate: A new U-shaped limit groove is added to prevent the edge banding from rebounding, floating up and down, and smooth tape feeding.
8.The meter counter is docked with a meter-counting tape, and the docking error is ±1mm.
9.Gluing assembly and hot air gun. The gluing assembly is used to apply glue to the edge strips and boards. It is double-sided glued for a better fit.
10.The hot air gun has the function of softening the edge banding strip and making the edge banding strip more firmly adhered.
11.Start-stop switch, the machine will automatically stop 5 seconds after the plate leaves the sensor, protecting workers' safety and saving energy.
12.No need to adjust the thickness of the board, quickly adapt to the thickness of the board, no manual operation required (14-70mm)
13.Scrape as you go. After trimming is completed, scrape off the excess edge strips and glue lines.
14.The circular stacked arm design has a stronger physical load-bearing capacity than the square stacked arm. The stacked arms are lightweight and more flexible in operation.
KN800 advantages:
1. Rotating double stacking arm structure: edge banding and trimming have their own stacking arms that work independently. The stacking arms of the edge banding part can be used for sealing and trimming (one person can easily seal large panels); two people can seal small panels at the same time with double arms to improve efficiency.
Ø The gantry milling machine at the installation site is milled flat to ensure parallelism and facilitate operation.
Ø The total length of the stacking arm is 240cm (excluding suction cups), the small arm is φ114mm, and the large arm is φ165mm; standard 30/14cm suction cups (can firmly absorb the board to prevent it from hanging and sagging, and the edge banding is fast and stable); load-bearing ≤120kgØ Processable (suction cups): round ≤3.8 meters square ≥0.4*0.4 meters ≤1.8*3.8 meters L-shaped ≤1.5*3.2 meters;
2. Opening and closing limiter and pressure strip assembly: automatically return to position when feeding the belt; automatically open when the edge banding belt is finished. (Avoid glue accumulation when the rubber roller rotates for a long time).
3. The angle of the edge banding and trimming assembly is adjustable: suitable for a variety of plates to increase compatibility. (Edge banding rotation angle ±35°, trimming rotation angle ±45°).
4. Stacking arm brake: Release the suction cup, the brake starts automatically to prevent the arm from swinging.
5. Adopt glue pot type glue coating assembly: ① PUR/EVA glue can be used alone; ② 7cm edge banding can be passed; ③ The glue pot capacity is 2600ml to avoid multiple glue additions; ④ Teflon coating to prevent glue hanging and glue accumulation, and improve utilization; ⑤ The extended knob glue amount adjustment is convenient and intuitive; ⑥ Single-sided edge banding glue coating (saving glue, small glue line).
6. One-key glue removal of the glue pot: directly click "one-key glue removal" on the touch screen, and different glues can be replaced quickly and conveniently.
7. Automatic glue removal spray: avoid glue adhesion at the laminating wheel and pressure strip plate.
8. Auxiliary hot air: heat the edge banding strip, soften the edge banding strip, and make the edge banding strip and the board stick more firmly.
9. New second-generation cutter assembly: ultra-fast response, ensuring the vertical accuracy of cutting (double-column balance, stable cutter, compact structure, good cutting flatness, cutting strip width up to 70mm, cutting strip thickness 3mm)
10. Meter-based tape cutting: set the length and automatically cut the tape (use this function when the straight edge length is greater than 40cm)
11. Data storage: 20 data can be stored
12. 4 limit positions: prevent the edge banding strip from moving up and down, and feed the tape smoothly.
13. Standard secondary auxiliary bonding wheel: the edge banding strip and the board are pressed twice to increase the bonding firmness.
14. The photoelectric device automatically senses the plate, and stops rotating if it does not sense the plate after 5 seconds
15. Profiling power wheel: When trimming, the plate rotates according to the speed of the profiling wheel, making the trimming smoother and more fluent
16. Trimming both upper and lower edges: The trimming knives rotate at the same time, and the upper and lower excess edge banding strips are trimmed at one time
17. Follow-up scraping: After trimming, scrape off the excess edge banding strips and glue lines (double bevel, high utilization rate)
18. PTFE gas column: fix the plate, automatically inhale, and prevent scratching the plate
19. Efficient dust collection: dense brush with 150mm thickened dust pipe, suck the debris into the vacuum cleaner (turn on the dust collection before trimming)
20. High-strength frame: body length 173cm width 207cm height 147cm (excluding arms, excluding support strips)
1. The maximum plate size processed by KN800 is larger. KN800: square 1.8*3.8m; round: diameter 3.8m; L-shaped: 1.5*3.2m/KN620-3: square 1.2*2.4m; round: diameter 2.4m; L-shaped: 1.4*1.6m
2. KN800 has 2 stacking arms, and the edge banding and trimming parts can work at the same time, with a longer length (KN800: 225cm/KN800: 240cm) and a stronger maximum load-bearing capacity (KN800: 120kg/KN620-3: 100kg).
3. KN800 has a stacking arm self-locking function, which can make the stacking arm swing when the ground is uneven.
4. KN800 uses a pneumatic pressure stripping plate, which can effectively prevent glue.
5. The stripping plate of KN800 is smoother and can prevent rewinding.
6. The edge banding head of KN800 can be adjusted to an angle of ±35°, the trimming head can be adjusted to an angle of ±45°; the head of KN620-3 can be rotated to ±15°.
7. The auxiliary hot air device of KN800 uses a visual Delixi hot air gun to fix the temperature.
8. The control screen of KN800 can be connected to the Internet and the system can be upgraded remotely.
9. The upper scraper of KN800 adopts pneumatic control, has a digital display function, and is smoother; the upper scraper of KN620-3 adopts gravity sensing, which can scrape the edge gently.
